Order by 11:00 and it rides today's truck · Fresno & Clovis dailyCounter open · 5889 E Clinton AveTeam login
MARCOINDUSTRY SUPPLIES · FRESNO

Pressure Washing · updated 2026-10

Concrete cleaning and oil stains: shop floors, driveways and packing-house slabs

Degreaser, detergent or rust remover, how long to let it dwell, hot or cold water, what to do about runoff, and when a sealer makes sense.

Concrete is porous. It looks like stone, but under a microscope it behaves more like a hard sponge, and anything that lands on it goes in. Oil goes in. Hydraulic fluid goes in. Forklift tire marks, dairy wash residue and the drip under a parked truck go in. That is why a pressure washer with plain water often makes a stain look better for an afternoon and then the stain returns as the slab dries and the oil wicks back to the surface.

Cleaning concrete is mostly a chemistry job followed by a rinse. The pressure part is the easy half.

Match the product to the stain

Three categories cover most of what we sell for concrete, and picking the wrong one is the most common reason a job does not work.

  • Detergent. A general-purpose concrete cleaner for dirt, tire marks, algae film, grease film and the grey haze on a driveway. The F9 Groundskeeper concrete maintenance cleaner on our shelf is this kind of product, sold from a gallon up to a 275-gallon tote for crews and facilities that clean a lot of slab.
  • Degreaser. For oil and grease that has gone into the surface. Degreasers are formulated to break oil into smaller pieces that can be carried away in water. The EBC EnviroBio degreaser is an example, and it is a good fit when you want something that works on petroleum without solvent smell.
  • Rust remover. For orange and brown iron stains: rebar bleed, steel shelving legs, irrigation water with iron in it, and the rust rings under metal cans. The F9 BARC rust and oxidation remover is on the Pressure aisle for this purpose. Rust does not come off with a degreaser, and an oil stain does not come off with a rust remover.

Read the label on every one of them, and the safety data sheet. Gloves and eye protection are the minimum. Do not mix products from different bottles in the same bucket, and do not apply a rust remover and a degreaser to the same spot at the same time. If a surface has more than one problem, treat one, rinse it fully, let it dry, and see what is left.

Oil on a shop floor

Start by removing whatever is still liquid. Absorbent granules or a shop towel lifts the loose oil, and sweeping it up is cheaper than washing it into the drain. Then wet the area lightly, apply the degreaser at the strength on the label, and work it in with a stiff deck brush so the product contacts the oil in the pores instead of sitting on top of it.

Dwell is where this job is won. Give the product the contact time the label states. For an old stain, that may mean repeating the application rather than leaving it to dry. Do not let the product dry on the slab on a hot day. In the Valley in July, a slab in direct sun will flash a degreaser dry in minutes, so work in sections you can cover before the product dries, or do the job early in the morning or in shade.

Rinse thoroughly. A degreaser that is not rinsed leaves a film that grabs dirt, and a slab with a film looks dirty again in a week.

Old oil stains often do not come out in one pass. A dark ring on a shop floor that has been there for years has had a lot of time to move. Expect to repeat, and expect that some staining may stay as a lighter shadow. Tell the customer that before you start.

Driveways and residential slabs

Driveways collect oil in a much smaller footprint, usually a spot or two under where the car sits. A degreaser applied straight on the spot, brushed and given time, then rinsed, does more than blasting it with a hot, narrow tip. Pressure on its own can etch the surface and leave clean stripes in an otherwise grey slab, which looks worse than the stain.

Keep the wand moving and the tip a consistent distance from the surface. A wide fan with chemical is a better tool than a narrow fan with force. Look at the pressure aisle guide on tips before you reach for a turbo nozzle.

Dairy, packing and processing slabs

A dairy parlor, a packing shed and a food processing floor each has a different mess: milk residue and manure film, fruit sugars and wax, grease from a cooking line. All of them are organic, and organic soils respond to a detergent and an enzymatic or biological product more than to a harsh chemical. Facilities like these also have rules about what can be used near food, so check with the person in charge of food safety before you bring in a product. Ask the facility which products are already approved.

These floors also tend to be wet most of the day, which changes how products dwell. Squeegee the standing water off first, apply the product to a damp, not flooded, surface, and rinse into the drain system the plant already uses for wash water.

Hot water or cold

Heat helps with oil and grease. A hot-water machine softens fats and speeds up a degreaser, which is why commercial kitchens and shops use hot-water washers. A cold-water machine can still do the work with a good degreaser, more dwell and some agitation. If the product label specifies a temperature, follow it. Hot water on some products flashes them or shortens the dwell, and in the summer the slab itself may be hot enough.

Rinse, runoff and stormwater

Washing a slab sends something somewhere. Oil, detergent and the soil they carry go with the water, and what you do with it matters both to the property and to the law.

This is a general caution and not legal advice. In California, wash water is not supposed to go into a storm drain, because storm drains lead to creeks and rivers without treatment. Rules on how wash water must be collected, filtered, or discharged to a sanitary sewer vary by city, county and by the type of site, and a business may need a permit. We do not know the rules for your particular site, and we cannot promise that any method complies. Before you do a large job, call the city or county, or the water district, and ask what applies. Many contractors use a berm, a drain cover and a wet vacuum to recover water. That kit is common, and the equipment aisle carries wet vacuums and floor extractors that can help.

  • Do not wash oil and degreaser toward a street gutter or storm inlet.
  • Block the drain, contain the water, and recover it.
  • Dispose of absorbents and recovered sludge according to local rules.
  • If a job involves fuel or hydraulic oil in volume, stop and ask a professional.

When to seal

A sealer makes sense on a slab that you want to be easier to clean next time: a shop floor, a garage, a dairy walkway, a driveway in front of a business. It does not make a slab stain-proof. It slows absorption, so a spill sits on the surface long enough to wipe up.

The Genlabs Sur-Seal concrete and masonry sealer is one example on the shelf. The surface has to be clean, dry and free of old oil, because a sealer over oil traps the oil, and the sealer peels. That means the degreasing step comes first, followed by a full dry time. Check the label for the temperature range and the cure time, and plan the job for a stretch of dry weather. In the Valley that rarely means waiting long, but a tule fog week can add days.

If you are pricing a concrete job and are unsure what to bring, the counter can look at a photo of the stain and tell you which of the three product groups to start with. Delivery on the route is free over the minimum, so you can order the gallon and the tote on the same truck.

More from the counter