Pressure Washing · updated 2026-10
Pressure washer tips, nozzles and hoses: matching the small parts to the machine
Orifice size against GPM and PSI, what the fan degrees do, V-jet or quick-connect, turbo nozzles, hose rating, lance length, and how a tip wears out.
A pressure washer is only as good as the last six inches of it. The pump can be perfect and the engine can be new, and a worn tip will still paint the driveway in stripes and make you think the machine is dying. Tips, hoses, lances and guns are the parts people replace, and nearly every bad result we hear about at the counter is a mismatch between those parts and the machine.
We do not sell pressure washer machines. What we carry in the Pressure aisle is the part of the system that wears out and the part that decides how the work looks: tips and V-jets, lances, a trigger gun, a turbo nozzle, and high-pressure hose.
Orifice size, GPM and PSI
The hole in the tip is the orifice, and its size is a number that is tied to the machine’s output. A pump makes flow, measured in gallons per minute. The tip is a restriction, and the restriction creates the pressure. The same pump with a smaller hole produces higher pressure; with a larger hole, lower pressure.
Tips are sized by a number, such as 3.5 or 6.5, and the usual convention is that the number is roughly the flow the tip passes at 4000 psi. A 3.5 tip on a machine that makes about 3.5 gallons a minute will run near the pressure the machine is rated for. Put a smaller tip on that machine and the pressure climbs above rating, which strains the pump and the unloader. Put a larger tip on it and the pressure falls and the stream turns weak and wide. Check the data on the tip package, because manufacturers differ, and use the machine’s own label for GPM and PSI.
- Too small an orifice: pressure above the machine’s rating, hot pump, shortened seal life.
- Too large an orifice: low pressure, lazy stream, no cleaning power, and a machine that unloads and cycles.
- Right size: the gauge sits at the rated pressure with the trigger held down.
The 3.5 and 6.5 sizes on our shelf cover the commonly used small-to-mid and high-flow machines. If your machine makes a flow somewhere between those, tell the counter the GPM and PSI from the nameplate and we will tell you what fits.
Fan degrees and what they are for
The degree of a tip is the angle of the fan it makes. Narrow fan, concentrated force; wide fan, gentle coverage.
- 0-degree is a pencil jet. Strong enough to cut, to chip and to damage. Most crews keep it in the truck only for stuck-on mud and then use it carefully.
- 15-degree is a narrow fan for heavy cleaning on hard surfaces: concrete, steel, heavy equipment, stripping paint.
- 25-degree is the general-purpose tip for most surfaces and most jobs.
- 40-degree is a wide fan for washing larger areas that need only moderate force: vehicles, siding, painted surfaces, fences.
- 65-degree is the widest and gentlest, used to apply soap through the gun or to rinse delicate work.
On our shelf you will find the 40-degree and 65-degree tips in brass and in stainless. Those are the two tips most people use for washing and rinsing, and they are the ones that cost the least damage if you slip. For concrete work, many crews use a rotating or turbo tip, below, rather than a narrow fixed fan.
V-jet or quick-connect
The V-jet is a tip that threads into the end of a wand or a lance. The alternative is a quick-connect tip, which snaps into a coupler at the end of the wand. Neither is better. The quick-connect lets you change tips in two seconds, and that matters if you move between a rinse tip and a soap tip all day. The V-jet is cheaper, has nothing that can leak at the coupler, and is a good fit on a lance dedicated to one job.
Both have to match the thread. Common machines use one size of quick-connect, and you will find that nearly every tip in a category fits it. Check the pressure rating on the coupler as well as the tip, because the coupler is the part most likely to fail first.
Turbo nozzles
A turbo nozzle spins a pencil jet in a tight cone. The result is the force of a narrow tip across the coverage of a wide one, which is why it cleans concrete faster than any fixed tip. It is also loud and it throws spray back at you, and it will etch a soft surface, so keep it off wood, vinyl siding and anything painted. The 5.5 GPM turbo nozzle on our shelf is sized for machines that make about that flow. Putting a turbo meant for a smaller machine on a larger one overloads the bearing and cooks it.
Hose rating and diameter
Pressure hose is rated by working pressure, and the rating has to be higher than the machine’s maximum pressure. The Continental ContiTech Neptune hose in the Pressure aisle is rated for 4000 psi and comes in 3/8 inch diameter. We cut it to length from one foot to 550, so you do not have to run a coupled pair when you need a single piece.
Diameter is a flow question. A narrow hose creates friction, and friction becomes lost pressure. At moderate flow, 3/8 inch is the standard and it works over short and medium runs. At higher flow or a very long run, the loss gets large enough to matter, and the pressure at the gun is lower than the pressure at the pump. If your machine pushes a high flow, or if you are pulling a hose across a packing-house yard, tell the counter the GPM and the length and ask before you buy.
- Do not use a garden hose on the high-pressure side. It will burst.
- Inspect the hose for bulges, cuts, and kinks where the wire braid shows. A hose that has been run over is not safe, even if it holds today.
- Do not repair high-pressure hose with clamps and tape. Replace the section or use a proper coupler.
Lances and trigger guns
A lance is the tube that puts the tip where you can reach. Ours come in 12, 14 and 20 inch stainless, and they are rated for 4100 psi. A longer lance saves your back on floors, truck beds and anything low. A shorter lance is easier in tight spaces, under equipment and along a wall. Twenty inches is a good all-around choice if you are only buying one.
The trigger gun is the part you hold, and it has a rating. The Suttner on our shelf is rated for 5000 psi and 12 GPM, which is more than most washers ask of it, so it will outlast the machine. The gun, the lance, the coupler and the hose all have to be rated at least as high as the machine. The weakest rating is the real rating.
Matching everything to the machine
Write down four numbers from the nameplate: maximum psi, GPM, the inlet fitting, and the outlet fitting. Then check each part against them.
- Hose: rated above max psi, diameter suited to GPM.
- Gun and lance: rated above max psi, flow rating at or above GPM.
- Tips: orifice sized to GPM at the machine’s operating pressure.
- Couplers: the same rating and the same thread as the lance.
If any link in the chain is under-rated, that link is the failure point.
How tips wear
A tip wears from the inside. Sand, grit and mineral scale scour the orifice and make it larger. The pressure drops a little at a time, so you do not notice it. What you do notice is the stripe pattern in the fan, or that a job that used to take an hour takes ninety minutes. Brass wears faster than stainless, which is why stainless is the choice for crews that run all day. Check by comparing the fan pattern against a tip you know is new, or measure the pressure at the gun.
Replace tips before they fail. Keep a spare in the truck of each size you use. And a small filter at the inlet of the pump will save every tip you own.
If you are not sure what you need, stop by the counter with the machine’s nameplate or a photo of it. We will walk through the parts with you.